Average Reviews:
(More customer reviews)The Logitech Harmony RF Wireless Extender allows your RF-equipped Harmony Remote (the 890, 895 or new 1000) to control components without having an IR "line of sight" to the components. One RF Wireless Extender is included with the Harmony 890, but it is unfortunately not included with the Harmony 1000.
Make no mistake, this device is an absolute REQUIREMENT for any large room or complex setup. In my configuration, the Harmony 1000 didn't have the strength to power all of my components through IR from 20 feet distance. The RF extender solved this problem, and now I can control my entire setup even from another room.
One RF Wireless Extender can control up to 8 components within the line of sight of the unit, or within line of sight of the 8 included IR emitters. You can add multiple extenders to your configuration if you have components in different rooms or areas that could not be served by one unit. Annoyingly, even if you have more than 8 components within the reach of the unit or the emitters the Harmony software won't let you assign more than 8 devices to a single extender.
IMPORTANT: You should try to setup and verify your Harmony configuration using IR-only if possible before adding the extender, even if you have to sit near your components or have cabinet doors open. This is because the Harmony software makes you connect and disconnect both the extender (which must be unplugged from AC power) and the remote each time you make a change. Setting up the Harmony first, by itself, with IR is much easier to make changes to the configuration.
After verifying I could control my components using IR-only, I added the RF Wireless Extender to my setup. The Harmony software updated to the latest firmware, and I have had no problems configuring it using both Mac OS X and Windows clients.
Setup is very easy. If all of your components are behind a cabinet, you can simply mount this "blaster" unit inside, at least 10 inches from the front of your components. Or, you can attach the 8 included wired emitters (in 4 pairs of 2) near the IR receivers of each component. The wires for each of the 4 pairs are roughly 7 feet long, splitting into 2 emitters that must be placed within 25 inches of each other. Also good to note is that the tape is strong enough to attach to your component, but not strong enough to leave any residue should you need to remove them.
Within the Harmony setup, you then assign each component to either IR or RF Extender control. Optionally, you can assign each component to a channel (A,B,C,D,blaster) which corresponds to the 4 sets of 2 wired emitters and base, or all channels which sends all commands to all emitters. I chose to specifically assign each component to its channel, which seems to give better performance. (TIP: label your emitter wires!)
Once configured, you connect the RF Extender and the Harmony Remote to your computer to download the configuration. Then, you must plug the RF Extender into the wall, and optionally attach the IR emitter wires. The Harmony remote must initially be "paired" with the RF Extender, which is done by pressing the "Connect" button on the extender, and following the prompts on your remote.
Operation was flawless. I could control all components from around my house! And, the performance of startup was much faster, I believe because I had assigned each component to a specific channel on the extender.
In my configuration, I was pleasantly surprised to find the RF extender is fast enough to send the repeated command sequences needed to accelerate up and down through the menus in my AppleTV. Great job, Logitech!
If there was one area where Logitech could make improvements it would be the supplied documentation, which attempts to be user friendly but in the process is so oversimplified it is of little use. Since Amazon doesn't allow half-star increments, I stand by my 5-star review, documentation withstanding.
Based on the large number of problems people had when this was first released a year ago, I was expecting issues, but it would appear that the latest firmware (RF Extender v2.4, Harmony 890 v4.7) and Harmony client software (v7.0.2) have resolved all issues for both Mac OS X and Windows users.
All in all, a highly recommended product - and a great value bundled with the matching Harmony 890 (see my review there). I have since upgraded to the Harmony 1000, but kept this extender to use with it. It's a shame that Logitech doesn't include the extender with the 1000, as it really is a requirement.
I would recommend this without hesitation.
Click Here to see more reviews about: Logitech Harmony RF Wireless Extender
Gain complete control of components that are hidden behind cabinets or walls. With a range of up to 100 feet, you can place your equipment out of sight, or even move it to the next room. Designed for use with the Logitech Harmony 1000 or 890 Advanced Universal Remotes, Z-Wave (RF) Technology enables remote control of audio, visual, lighting, climate, and security systems without direct line-of-sight.Use additional receivers to control multiple entertainment systems.
Get 32% OFF
Click here for more information about Logitech Harmony RF Wireless Extender
No comments:
Post a Comment